Students design, build and evaluate a spring-powered mouse trap racer. For evaluation, teams equip their racers with an intelligent brick from a LEGO© MINDSTORMS© NXT Education Base Set and a HiTechnic© acceleration sensor. They use acceleration data collected during the launch to compute velocity and displacement vs. time graphs. In the process, students learn about the importance of fitting mathematical models to measurements of physical quantities, reinforce their knowledge of Newtonian mechanics, deal with design compromises, learn about data acquisition and logging, and carry out collaborative assessment of results from all participating teams.

Students conduct an experiment to determine how varying the composition of a construction material affects its strength. They make several adobe bricks with differing percentages of sand, soil, fibrous material and water. They test the bricks for strength by dropping them onto a concrete surface from progressively greater heights. Students graph the experiment results and use what they learn to design their own special mix that maximizes the bricks' strength. During the course of the experiment, students learn about variables (independent, dependent, control) and the steps of the engineering design process.

The lesson begins by introducing Olympics as the unit theme. The purpose of this lesson is to introduce students to the techniques of engineering problem solving. Specific techniques covered in the lesson include brainstorming and the engineering design process. The importance of thinking out of the box is also stressed to show that while some tasks seem impossible, they can be done. This introduction includes a discussion of the engineering required to build grand, often complex, Olympic event centers.

This art history video dicussion examines "Orsanmichele", Florence, 1349 loggia (1380-1404 upper stories).

Student groups are challenged to create food packages for specific foods. They focus on three components in the design of their food packages; the packages must keep the food clean, protect or aid in the physical and chemical changes that can take place in the food, and present the food appealingly. They design their packaging to meet these requirements.

The difference between an architect and an engineer is sometimes confusing because their roles in building design can be similar. Students experience a bit of both professions by following a set of requirements and meeting given constraints as they create a model parking garage. They experience the engineering design process first-hand as they design, build and test their models. They draw a blueprint for their design, select the construction materials and budget their expenditures. They also test their structures for strength and find their maximum loads.

Students learn about population density within environments and ecosystems. They determine the density of a population and think about why population density and distribution information is useful to engineers for city planning and design as well as for resource allocation.

Students continue to explore the story of building a pyramid, learning about the simple machine called a pulley. They learn how a pulley can be used to change the direction of applied forces and move/lift extremely heavy objects, and the powerful mechanical advantages of using a multiple-pulley system. Students perform a simple demonstration to see the mechanical advantage of using a pulley, and they identify modern day engineering applications of pulleys. In a hands-on activity, they see how a pulley can change the direction of a force, the difference between fixed and movable pulleys, and the mechanical advantage gained with multiple / combined pulleys. They also learn the many ways engineers use pulleys for everyday purposes.

Working individually or in pairs, students compete to design, create, test and redesign free-standing, weight-bearing towers using Kapla(TM) wooden blocks. The challenge is to build the tallest tower while meeting the design criteria and minimizing the amount of material used all within a time limit. Students experiment with different geometric shapes used in structural designs and determine how design choices affect the height and strength of structures, becoming comfortable with the concepts of structural members and modeling.

Student teams assign importance factors, called "desirability points," the rock properties found in the previous lesson/activity in order to mathematically determine the overall best rocks for building caverns within. They learn the real-world connections and relationships between the rock and the important engineering properties for designing and building caverns (or tunnels, mines, building foundations, etc.).

Students explore whether rooftop gardens are a viable option for combating the urban heat island effect. Can rooftop gardens reduce the temperature inside and outside houses? Teams each design and construct two model buildings using foam core board, one with a "green roof" and the other with a black tar paper roof. They measure and graph the ambient and inside building temperatures while under heat lamps and fans. Then students analyze the data and determine whether the rooftop gardens are beneficial to the inhabitants.

This art history video discussion looks at Saint Peter's Basilica and the numerous architects (see below) who contributed to Saint Peter's Basilica (Basilica Sancti Petri in Latin), begun 1506 completed 1626, Vatican City. Architectural contributors include: Donato Bramante who's design won Julius II's competition; Antonio da Sangallo, a student of Bramante, designed the Pauline Chapel; Fra Giocondo strengthened the foundation; Raphael worked with Fra Giocondo, his redesigned building plan was not executed; Michelangelo designed the dome, crossing, and exterior excluding the nave and facade; Giacomo della Porta, designed the cupola; Carlo Maderno, extended Michelangelo's plan adding a nave and grand facade; Gian Lorenzo Bernini added the piazza, the Cathedra Petri, and the Baldacchino.

This art history video discussion looks at Basilica of Santa Maria Maggiore, Rome, 5th century A.D.

This unit describes a general approach to guiding students to complete service-based engineering design projects, with specific examples provided in detail as associated activities. With your class, brainstorm ideas for engineering designs that benefit your community or a specific person in your community. Then, guided by the steps of the engineering design process, have students research to understand background science and math, meet their client to understand the problem, and create, test and improve prototype devices. Note that service-based projects often take more time to prepare, especially if you arrange for a real client. However, the authors notice that students of both genders and all ethnicities tend to respond with more enthusiasm and interest to altruistic projects.

Students are introduced to the concepts of graywater and water reuse within households. They calculate the amount of used water a family generates in one day and use a model of home plumbing to find out how much graywater is produced in homes every day. They graph their results and discuss energy efficiency implications. Students are then challenged to find ways to reduce water use within the home.

Students learn about how engineers design and build shake tables to test the ability of buildings to withstand the various types of seismic waves generated by earthquakes. Just like engineers, students design and build shake tables to test their own model buildings made of toothpicks and mini marshmallows. Once students are satisfied with the performance of their buildings, they put them through a one-minute simulated earthquake challenge.

Students learn about the major factors that comprise the design and construction cost of a modern bridge. Before a bridge design is completed, engineers provide overall cost estimates for construction of the bridge. Students learn about the components that go into estimating the total cost, including expenses for site investigation, design, materials, equipment, labor and construction oversight, as well as the trade-off between a design and its cost.

Skyscrapers are one of the most glorified products of Civil Engineering and contain an interesting history of progress and development. In this lesson, the students will learn about the history of the world's tallest free standing structures and the basic design principles behind their success. Students will build their own newspaper skyscrapers with limited materials and time, trying to achieve a maximum height and the ability to withstand a "hurricane wind" force. Discussion will concentrate on materials, forces that a skyscraper needs to withstand, and basic structural design.

Students explore building a pyramid, learning about the simple machine called an inclined plane. They also learn about another simple machine, the screw, and how it is used as a lifting or fastening device. During a hands-on activity, students see how the angle of inclination and pull force can make it easier (or harder) to pull an object up an inclined plane.

Students explore why different types of sneakers are used in a variety of common sports, and how engineers analyze design needs in sneakers and many other everyday items. The goal is for students to understand the basics of engineering associated with the design of athletic shoes. The design of footware based on how it will be used involves bioengineering. Students analyze the foot movements in a variety of sports, develop design criteria for a specific sport, and make recommendations for requirements for the sneakers used in that sport.